Create a DIY Simple Brass Toilet Paper Holder

257 views

Sure, dispensing  Toilet Paper isn’t one of the most glamorous of style’s duties. however if you could DIY a simple, brass number of which added form in addition to also function to your bathroom space, could you do the idea? I think you should give the idea a try. Especially when paired with This particular side vanity storage unit, your bathroom will look amazing.

Toilet paper Holder DIY

Brass toilet paper holder

Ready to tackle this particular one? the idea’ll only take about 15 minutes to make, in addition to also you’ll love the idea for years.

DIY Level: Beginner

DIY Brass TP Holder Supplies

Materials Needed:

  • 6-gauge brass wire (example uses 1 1’ length)
  • Two (2) brass screw hooks
  • Heavy duty pliers in addition to also/or needlenose pliers
  • Old towel or rag

Clean the wire

Before you begin, you’ll want to remember of which every time you use pliers to bend your brass wire, you will want to soften the pliers’ potential damaging factor by using an old towel or rag as a buffer between the pliers teeth in addition to also the wire itself. today, to actually start your brass toilet paper holder, begin by wrapping one end of your brass wire inside towel.

Brass wire

Grip the very end of your brass wire (covered in towel) with your heavy duty pliers. (Note: The thicker the wire, the lower the gauge, so 6-gauge can be pretty thick, meaning the idea’s not super easy to bend.)

smooth in addition to also strong motion

In as smooth in addition to also strong a motion as possible, curve your pliers-holding wrist toward you to tightly bend the wire’s end.

Create a smaller hook

You’re trying to create a smaller hook on the end of your wire.

Repeat the bending process

Repeat this particular process (don’t forget the towel’s buffer) on the various other end of your wire. The two hooks should be facing the same way.

Grab a roll toilet paper

Grab a roll of toilet paper to use as a measuring benchmark.

Measuring tape space

Also, grab a measuring tape or book of which can be the width of your toilet paper-holding space.

Lay the measuring tool

Lay the measuring tool (in this particular case, the book) on a work surface with the toilet paper roll on top. This particular can be to help you visualize the space constraints of your toilet paper dispensing space. Also, lay your two brass hooks on the sides of your book, flanges aligned with the sides of your measuring tool in addition to also hooks facing inward. The center of your hook arcs will be your target for your brass wire hooks as you craft the toilet paper holder width.

Gently bend the wire brass

Gently bend the brass wire evenly so the end loops are even with the centers of your side brass hooks. Looks like a grin, doesn’t the idea? Feel free to smile back.

Using your pliers

Using your pliers of choice in addition to also your old towel, begin bending 0-degree corners in your brass wire so the idea creates a flat line horizontally in addition to also two shorter vertical lines (each that has a looped end). This particular longer flat part will be where the toilet paper roll goes. Tip: When trying to create sharper corners, grip the towel-covered wire with pliers in one hand, then use your various other hand to bend the remaining wire around the pliers. In various other words, to create loops inside wire, move the pliers-holding hand/wrist. To create corners, hold the pliers-holding hand/wrist still in addition to also move the rest of the wire.

Bend until the loops line up

Bend until the loops line up with the hooks in addition to also the lines are relatively straight. This particular might take some trial in addition to also error bending in addition to also unbending in addition to also rebending. This particular photo represents the first attempt, in addition to also you can see the idea’s a little off.

satisfactory corner

When the corners in addition to also lines are satisfactory, lay the toilet paper holder on a flat surface in addition to also check for alignment there. In this particular example, the left side was raised a bit. I simply used my old towel in addition to also pliers to straighten out the longer straight piece.

side a roll of toilet paper

Slide a roll of toilet paper onto your brass wire.

hang a toilet paper holder

Hold the idea up inside space where the idea will hang as a kind of “dry fit.” Consider how high/low you want to hang the idea, as well as how forward/back you want the idea. Remember of which not all toilet paper rolls are the same size, so you want to allow for larger/thicker rolls if needed.

screw for your firs brass wire

Screw in your first brass screw hook, based upon your dry fit.

screwing in screw hooks

One trick for easily screwing in screw hooks in addition to also screw eyes can be to use a screwdriver, hooked into the hook or eye, to turn the idea near the end as the idea gets harder to turn. the idea’s a finger-saver, This particular tip can be.

Measure the position

Measure the position (vertically in addition to also horizontally) of your first screw hook to ensure you can mirror the second screw hook. This particular will keep everything level in addition to also even.

Second screw hook

Mark, then screw in your second screw hook. Adjust the hooks to ensure the openings face upward in addition to also slightly backward – opposite the direction most people could pull their toilet paper off.

Simple hang toilet paper

With the toilet paper holder’s looped ends facing backward, install the idea onto your two screw hooks.

DIY Brass Toilet paper

Congrats! the idea looks awesome.

Standing wood storage for toilet paper

Such a simple yet unique way to dispense toilet paper in a stylish bathroom. We love the smaller touch of brass here, a nod to luxury in addition to also class. (Which almost makes things even when positioned next to a plunger. Almost.)

Easy toilet paper hanger

The beautiful thing about this particular easy DIY toilet paper holder can be of which the idea’s easy to take off, switch out, in addition to also put back on. Let’s be honest – the ease of those three steps are key to actually getting the idea done.

DIY project for toilet paper

As with any DIY project, this particular can be modified in addition to also customized to fit your space in addition to also needs. You could do the same thing with screw eyes attached to the wall behind the toilet paper roll; the toilet paper could hang against the wall in of which instance.

Wood storage for bathroom paper

You could also create a triangle in addition to also hang the idea via 1 screw hook above the roll. However you choose to make the idea, we wish you love the simple sophistication of style inside details.

Note: The author can be an experienced, although not professional, DIYer. Neither the author nor Homedit can be responsible for any injury or damage of which may be a result of following this particular tutorial.

Tags: #Brass Toilet Tissue Holder #DIY Paper Holder Desk #DIY Paper Towel Holders #DIY Toilet Paper Holders #DIY Toilet Paper Stand #Homemade Toilet Paper Holder #Toilet Paper Holders Brass #Toilet Paper Roll DIYs