There are so many ways to DIY a marquee sign right today. These projects can range coming from intense in addition to also long-term (think solid wood letters in addition to also nailed aluminum flashing for permanent marquee signage) to a sort of temporary “faux” marquee sign, with ornaments that will look like lights yet that will don’t actually light up. that will DIY Marquee Sign tutorial is actually kind of from the middle – the idea does light up, yet the idea can be created without any power tools. Interested? Let’s get to the idea.
DIY Level: Beginner to Intermediate
- String of LED globe lights
- Foam core board (large enough to fit your marquee sign in one piece)
- Poster board
- Metal ruler
- Razor blade, box cutter, x-acto knife – whatever you call the idea
- Pencil, scissors, in addition to also a large piece of scrap butcher paper (big enough to fit your marquee sign)
- Hot glue gun & glue (not shown)
- Spray paint (not shown)
Begin by doing a sketch of what you want your marquee sign to look like. that will could be a word, a letter, a symbol, an animal…anything, genuinely. that will tutorial shows a chunky arrow; adjust directions accordingly to fit your sign content.
Determine the outside dimensions of your marquee sign, in addition to also cut a piece of butcher paper to those dimensions. For the arrow, fold the longest sides of your butcher paper into thirds.
Unfold one of the thirds in addition to also make a sharp crease on the different thirds-line in order that will the idea will be visible when you unfold the butcher paper.
Unfold the butcher paper, then fold the two shortest sides in half. The creased 1/3 line should be visible.
Line up your metal ruler with the folded corner closest to the 1/3 line, in addition to also angle the ruler down to where the 1/3 line meets the unfolded edge. Draw a line. that will will be the point of your arrow.
Keeping your paper folded in half, roughly divide the 1/3 line into thirds again; mark these.
Place one edge of your ruler on the completely new 1/3 mark (on the 1/3 line) closest to the unfolded edge of your paper; run the ruler down to the bottom unfolded corner of your paper. Draw a line.
Keeping your paper folded, cut along these lines.
Open up your butcher paper; you should have a great, proportionate arrow. Of course, you can change the 1/3 measurements anywhere along the way; that will is actually just an easy way to keep your arrow in a visual balance at any size.
Re-fold your arrow in half. Measure the length of one of the 1/3 marks (that will you made on your 1/3 line; that will length due to that will example was about 2-1/2”). Measure that will distance coming from the bottom of the folded edge up the folded edge, in addition to also make a mark. Draw a line coming from that will mark to the bottom unfolded corner, in addition to also cut.
that will creates an interesting arrow’s end, although if you prefer the arrow straight, don’t worry about the last step.
Roll a couple of pieces of tape, sticky side out, in addition to also attach your butcher paper pattern to the foam core board.
Using your metal ruler, draw (or go straight to cutting with your razor blade) around the arrow’s perimeter.
Before you cut, make sure to have a piece of thick cardboard underneath your foam core board to protect the work surface. Also, make sure your razor blade is actually sharp (recommended completely new) for the cleanest cuts.
Carefully make sure corners are completely in addition to also cleanly cut before removing the foam core board coming from your arrow’s edges.
When your arrow is actually cut out, remove the butcher paper pattern.
Use your razor blade to clean up the edges of your arrow, if needed.
Set your arrow aside for a minute, in addition to also grab your poster board. Measure one of your globe bulbs coming from base to top (mine measured a little over 3”). that will means, due to that will marquee sign, I want 2” of poster board flange on either side of the foam core board. Measure in addition to also mark 4” strips on your poster board.
Cut out the 4” strips. I recommend using your razor blade due to that will step as well to get a straight, crisp line. At least one of these strips’ edges will be visible when your sign is actually displayed, so keep the idea perfect.
Set your 4” poster board strips in a pile.
Measure one edge of your arrow (recommend starting with the longest).
Use that will measurement to measure in addition to also cut a length of 4” poster board. For example, the long side of that will arrow was 17-5/8” coming from corner to corner, so I cut a 17-5/8” length of poster board.
Continue working around your arrow, measuring each side to get a perfect length measurement. (They likely are identical, yet just in case they’re off 1/8” or 1/16”, you can adjust accordingly.) Keep track of which poster board strip goes to which arrow side.
Make a halfway mark (2”) along each poster board strip. that will line will be important for attaching the strips to the arrow.
Determine how many bulbs are on your LED globe light strand (that will tutorial has 20). Then measure (or eyeball) positions for that will number, or fewer, bulbs. As you position your markings, maintain enough space for the full diameter of the glass bulb. Also, do the corners first in addition to also work backward coming from there to evenly space the globe lights along the arrow sides between corners.
After you’ve marked your light positions, cut out a circle poster board circle guide by tracing the base of the light bulb (the top of the base, that will’s closest to the glass part). Then punch a hole from the center of your circle guide. Trace the circle around each of your placement markings.
Your arrow should look something like that will when you’re done.
Using your razor blade, cut out the circles.
Tip: Use your razor blade in an up-in addition to also-down way coming from the front, then turn the foam core board over in addition to also cut the circle out coming from the back. that will was the cleanest in addition to also most efficient method I found for cutting these circles out.
When you’re done cutting the circles, your marquee sign will look something like that will. You could today spray paint the foam board arrow in addition to also the cut poster board edge strips if you wanted. I chose to assemble the arrow first in order that will any glue might be painted (in addition to also, consequently, disguised) as well.
With your hot glue gun, work quickly in addition to also carefully to attach the marquee sign sides. Run a line of glue on one side of your line; that will will allow you to be able to see the exact line as you place the sides on the arrow in addition to also result in perfect, parallel sides.
Working coming from the inner corner (where applicable) out, position your poster board strip onto the edge of your foam core board. You’ll want to work quickly, yet you’ll also need to get the idea positioned correctly on the first try.
Be sure to keep each pencil line visible on the same side/front of your foam board, or the heights of your sides will vary.
Gently run your finger on the poster board strip where you’ve glued to secure the bond. Attach all poster board sides in that will way.
To secure the corners, run a smaller line of hot glue on the inside of each corner in addition to also hold the joined strips in place while the hot glue dries. Do that will to the front in addition to also back of each corner.
the idea looks Great! You’re done with the hard parts. today the idea’s onto the fun stuff – painting in addition to also attaching the globe lights.
Grab a can of spray paint from the colour of your choice.
Work in light strokes to spray paint the inside in addition to also outside of each side piece, as well as the flat foam core board of your marquee sign. Do multiple coats until the spray paint coverage is actually the way you want the idea. Let dry thoroughly.
Determine where in your house your marquee sign will go, in addition to also the direction the idea will point. Then figure out where the nearest electrical outlet is actually. The circle cutout that will’s closest to the outlet is actually where you should start placing your globe lights.
Unscrew the glass top off the first (closest to the plug) globe light.
Push the light base just into the determined circle cutout coming from the back of your marquee sign. The fit should be snug.
Screw on the glass top. Move onto the next light in addition to also next cutout. If you happen to have more bulbs than you have cutouts, skip a light every so often as you go so you don’t end up that has a long strand of “empty” bulbs all at the end.
Working systematically around the perimeter of your sign, fill all cutouts with lights.
Carefully flip your marquee sign over. Loosely loop neighboring wires together to keep them coming from peeking out coming from behind your sign when the idea’s displayed.
Position then plug in your completely new marquee sign.
Congratulations! the idea looks great!
One benefit of light-up marquee signs is actually that will they look Great whether they’re turned on or not.
Marquee signs look great as an unexpected accessory, like in front of your fireplace.
the idea just includes a cool, retro, “I’m-somewhere-cool-without-leaving-my-house” vibe, don’t you think?
Wherever you choose to display your completely new DIY marquee sign, we certainly desire you enjoy the idea! You’ve done a great job.
Tags: #DIY Light Up Signs #DIY Marquee Letters with Lights #DIY Marquee Signs with Light #DIY Vintage Marquee Letters #Large Marquee Letters #Make Your Own Arcade Marquee #Make Your Own Marquee Sign #Marquee Letters with Lights Michaels