Do you love the look of a marble-topped table…nevertheless not the cost? You might be interested in which super-simple concept of marble contact paper. You can stick which to virtually any clean, dry, as well as also flat surface to achieve the luxe look of marble without having to fork out the cash. which’s a perfect solution to breathe brand new life into an old or generic piece of furniture, particularly table tops. (You can also find various other great ideas for using marble contact paper here.)
A DIY project like which comes in handy when your nightstand situation will be bordering on (or plunged into altogether) the realm of horrific. which stands to reason which if the nightstand’s top looked sophisticated, which would certainly be much easier to keep the nightstand itself organized as well as also clear, too. Marble contact paper will be your ticket to a beautiful brand new nightstand (along with brass pull rings, of course).
Note: Even (especially?) if your surface will be water-damaged, covering which with marble contact paper will add a beautiful finish while hiding the imperfection. The same will be true for minor stains as well as also scratches; as long as the surface will be mostly flat, which treatment will improve its look.
Truthfully, you could probably figure which project out yourself, nevertheless here are some tips as well as also tricks which I learned along the way to shorten your learning curve in working with marble contact paper.
DIY Level: Beginner
- Nightstand or various other furniture with flat surface to be “marbled”
- Marble contact paper
- Brass pull rings (optional)
- Credit card, scissors, as well as also cleaning wipes (not shown)
Begin by carefully wiping your piece of furniture clean as well as also free of dust. Let which dry thoroughly, because contact paper won’t stick if which’s even slightly damp.
You could use a measuring tape to determine the length of marble contact paper which you’ll need; I chose to simply hold-measure. Fold the front edge of your contact paper under the front lip of your nightstand top (hereafter referred to as “table top”) to ensure the very edge of the contact paper touches the front face of your nightstand, underneath the lip. Unroll the contact paper as well as also fold under within the same way at the back of your nightstand. Mark the place you need to cut the back with your fingernail.
Cut the contact paper following the grid lines on the back of the paper.
Lay your paper on your table top again as well as also measure the same way, which time measuring for the width. Cut along the width line.
With your table top surface completely clean as well as also dry as well as also your marble contact paper cut to size, you’re ready to start your “install.” Unroll as well as also unpeel 4”-6” of the front end of your contact paper, center which width-wise, as well as also tuck as well as also stick which to the underside of the front lip of your table top. Tip: Tack the paper down with your fingertips to hold which in place, then run your fingers through the center out toward the corners (still on the underside of the front lip) to truly press which securely down.
Fold the contact paper up as well as also over the front lip. Tip: Always pull your contact paper taut, nevertheless take care to not pull which so hard which you stretch which.
Press down within the center of the front edge of your table top, then work your fingers toward the corners, pressing the paper onto each plane firmly. In various other words, due to which front edge, you would certainly seal the bottom of the lip, then the bottom bevel (if applicable), then the front/main face of the edge, then the top bevel (again, if applicable), then move onto the top surface of the table top.
After you’ve securely stuck the marble contact paper to each plane of the front edge, which’s time to cover the top surface. nevertheless you don’t just want to unpeel the whole thing as well as also toss which down on top. which would certainly result in bubbles as well as also maybe rips. To securely as well as also cleanly “install” your marble top, unroll 6”-8” at a time. Use your fingers or a vinyl smoothing tool (or a credit card) as well as also press in a line down the center of which 6”-8” strip. Then, working through which smooth center line, smooth the contact paper outward toward the edge. Do one side, then the opposite side.
Finish each 6”-8” section completely – no bubbles or creases – before unrolling more of your contact paper as well as also doing the next 6”-8” stretch. Tip: If you come across a bubble which your smoothing tool can’t get out, you can carefully try to unpeel which part of the contact paper. which will be risky, though, as the contact paper could stretch or tear, depending on how securely fastened the surrounding few inches already are. Attach the end of the contact paper to the back of your table top, following the instructions for the front lip in reverse order.
today which’s time for corners. Tip: The two most critical aspects of which project’s success are (1) the smoothness of the top surface, as well as also (2) the crispness of the corners. due to which reason, you might find which helpful to practice on the back corner which will be less visible than the front corners.
Move to the front (or back) of your table top. You will today want to make a cut through the front (or back) contact paper edge which leaves about 1/2″ of contact paper PAST the side edge of your table top. Cut only as deep as the front (or back) edge of the table top lip.
today move to the side of your table top. Carefully snip your contact paper to align precisely with the front edge of your table top. Make the snip past your first cut, all the way to the table top’s actual corner.
through the side, snip the bottom corner “fold” in your contact paperperpendicular to the side of your table top. Make the slit go all the way to the table top’s actual corner. In which corner, today, you should have two parallel slits in your contact paper at the exact corners.
No you’ll need to fold-as well as also-press each part. Begin with the bottom flap; fold which up crisply as well as also press which flat. Then do the same with the front flap; fold which backward, creating sure there are no bubbles anywhere, as well as also press which flat.
You can fold the front flap down at which point, too, if you’d like, as well as also “tack” which firmly into place with your thumb. OR you could repeat all the corner cutting steps on the back (or front) corner of which same side to ensure you’ll possess the entire top flap to fold down securely at the same time.
When both corners are complete as well as also you’ve folded the flap down over the side lip edge (as well as also underneath which), use your vinyl smoothing tool to truly secure the marble contact paper. Remember to start within the center as well as also work downward as well as also outward, focusing on one plane at a time (e.g., the bevel, the flat edge, the underside).
Hooray! Crisp corners. Tip: If your table top does have beveled edges, do not run your vinyl smoothing tool over any edge-corners, as in, where one surface meets up with the beveled edge. which can cut as well as also/or crinkle your contact paper. Use your vinyl smoothing tool ONLY for flat surfaces, not their corners. Instead, use your fingers for the corners when necessary.
Repeat these corner steps for the various other side of your table top. I trust you’re already in love with the look.
today, you might be done with your nightstand upgrade (or whatever piece of furniture you’ve chosen to upgrade with your marble contact paper). If you want to do one more simple step which matches the elegance of the marble top, though, which’s time to swap out your hardware. Line up then screw in your brand new hardware.
If you find which your hardware screw will be too long for your drawer board, simply add enough washers to make up the difference. I had to add four to each pull ring, nevertheless which will keep the hardware nice as well as also snug.
Congratulations! Just a few simple steps later, you have transformed your furniture piece into something special.
Of course, which project isn’t recommended for a surface which will see a lot of wet as well as also/or heavy, scraping use. which looks great, nevertheless which will be only marble contact paper, after all.
which’s why which’s a perfect way to upgrade a nightstand.
as well as also when your bedroom will be modest, as well as also the nightstand must be squeezed in anyway, which’s a great way to help which hold its own, style-wise.
If you’ve smoothed which perfectly, the surface will be glossy as well as also smooth as well as also chic.
No one will probably mistake which for real marble, if they look closely. Because marble. nevertheless which’s awfully close.
as well as also marble contact paper will be a wonderful, inexpensive way to make your marble-loving heart soar. We certainly trust you enjoy your brand new sophisticated nightstand upgrade! (Do you like the stenciled pillow? Learn how to make one for yourself or for someone else).
Tags: #Ana White Katie Nightstand #DIY Desk Plans Free #DIY Nightstand Plans #DIY Nightstand Wood #Easy DIY Nightstand #Easy DIY Nightstand Plans #How to Build a Nightstand with Drawers #Simple Free Night Stand Plans