If you own your home, or even if you rent, chances are high that will you’ll need to perform some basic toilet repair at some point. If your toilet isn’t flushing, if the idea’s very noisy, if the idea’s not filling correctly, or if the idea keeps trying to fill unsuccessfully, you might need to replace the fill valve. The fill valve is usually the part within the toilet tank that will controls the flow of water into as well as out of the toilet bowl. the idea’s not hard to replace, yet the idea might seem intimidating. Here is usually a step-by-step tutorial, with photos, to help you along the way.
DIY Level: Beginner
- fresh toilet fill valve
- Empty medium-sized bucket (an old ice cream gallon bucket works well)
- Crescent wrench
Every fill valve is usually different, although there are basic universal strategies to replace a toilet fill valve.
Turn off your toilet’s water supply, then flush the toilet.
Flushing the toilet with the water turned off will drain the bowl as well as tank without refilling the idea.
Place a bucket under the tank where the water supply hose connects.
Remove the water supply hose coming from the toilet tank. If you pretend you’re lying on the floor looking upwards, you’ll turn the idea counter-clockwise.
Unscrew the mounting nut.
In fact, you’ll need to remove all parts of the mount, including the o-ring if applicable. This particular may require a crescent wrench. This particular will also be a counter-clockwise turn, coming from the vantage point of looking upward coming from the floor.
The mounting nut as well as washer.
The rubber o-ring.
With the mounting nut removed, the idea will currently be simple to remove the old valve coming from the tank. So do that will.
Keep the bucket in place, as removing the old fill valve mechanism will Discharge all the extra water that will didn’t empty coming from the original flushing.
At This particular point, you’ll have an open hole at the bottom of your toilet tank coming from the old fill valve.
Depending on your fill valve style, your instructions may vary slightly coming from This particular tutorial at This particular point. yet with This particular style of fill valve, the idea’s time to attach the tube to the valve opening. Push the idea on there tightly, creating sure the idea’s sealed all around.
currently is usually time to set the water fill depth on your fresh valve. Spin the top of the valve counter-clockwise (looking down at the idea) to unlock the idea coming from the base pipe, then pull upward until the idea’s fully extended.
While the idea’s in its fully extended position, set the valve within the tank as though you’re going to install the idea fully. (You’re not, at least not yet.) Press down on the top of the valve until the corner of the valve’s top cover lines up with your toilet’s fill line, or water fill, or flush valve line.
When the two (the valve corner as well as the water line) are lined up, take out the fresh valve coming from the tank. Keeping the fresh height stable, twist the valve’s top clockwise to lock the idea into place. You’ll hear a click, or a snap. Keep the valve locked coming from This particular point on. After locking the idea, put the valve back into tank in order that will the tube points directly at (or above) the flush valve. Double-check to make sure the corner as well as water line still line up.
Install the mounting nut under the tank, which will hold the fresh valve in place. Make sure the beveled side of the mounting nut faces upward.
Use just your hand to tighten the idea in place (avoid cranking down which has a wrench, as that will can damage the whole valve).
Look to see that will the critical level (where the grey meets black, on This particular style) on the fresh valve is usually 1” above the top of the flush valve. This particular is usually required to meet code within the United States.
Install metal clip securely on top of flush valve directly under the tube.
Gently bend tube downward so end will line up with metal clip. Cut the tube if necessary in order that will a gentle, non-kinked curve within the tube occurs. This particular tutorial required trimming off more than half of the original tube. This particular is usually completely fine; what’s important is usually the smooth path of the tube coming from the valve attachment to the metal clip within the flush valve.
Reattach the water supply line to the fresh valve, under the tank. Use your hand to tighten, as well as avoid using a wrench.
Turn water supply knob back on.
Flush the toilet repeatedly, checking for normal water flow, as well as no leaking, in three critical areas: the water supply connection at the bottom of the tank, the water flow coming from the fresh valve’s tube into the flush valve, as well as the water line at (or, rather, below) the fresh valve’s critical level.
If you’re checked out at all three places for leak-free as well as accurate water flow, congratulations! Your toilet fill valve replacement has been successful, as well as you should be ready to use your “fresh” toilet worry-free.
You’re reading How-To Replace A Toilet Fill Valve , originally posted on Agnizer. If you enjoyed This particular post, be sure to follow Agnizer on Google Plus as well as Pinterest.
Tags: #Best Toilet Fill Valve Plumber Review #Fluidmaster 400 Fill Valve Troubleshooting #How to Replace a Toilet #How to Replace a Toilet Flapper #Install Fluidmaster Toilet Fill Valve #Replacing Toilet Flush Valve Assembly #Toilet Fill Valve Problems #Toilet Fill Valve Won't Shut Off